The Bushing of the Skateboard trucks, rubber pads for friends, are those two urethane rings that fit around the pivot of the skateboard trucks, between the hanger and the base and serve to steer the board with the right resistance that to cushion . Often considered only "details" and widely underestimated, bushing can radically change the feeling and behavior of a board by influencing steering and stability.
In each skateboard truck there are two rubber pads, for a total of 4 bushing per board. Bushing is present in almost all types of skate, including surfskates. We said almost because there are exceptions that may concern the number of bushing present or their absence in particular trucks (for example the surfskate slides do not have bushing in the front truck, just to cite a famous example).
Apart from the number of rubber pads, what is important to know is that not all rubber pads are the same. Bushing can have different shapes and different hardness.
A stiffer bushing will result in a more stable board but also harder to lean, which can be an advantage when performing tricks. While softer rubber pads increase steering and therefore are a better option for carving use on the roads or surfskate. In addition to hardness, the grommets can be easily adjusted to suit your needs, within a certain range, simply by tightening or loosening the nut that holds them in place.
Hardness of the bushing
As we have said, the bushing used in skateboarding exist of various hardnesses generally measured, a bit like it also happens for the wheels, on a Durometer Scale ranging from 60A to 100A where 60 is softer and 100 is the maximum hardness. Example 78A, 90A etc.
The hardness of the bushing must be chosen based on 2 factors: the weight of the skaters and the use to be made of them.
In general it can be said that 78A bushing are suitable for very light skaters, kids or riders who prefer carving over stability. On the other hand, 90A rubber pads are suitable for heavier people or those seeking greater stability.
The reason why bushing should always be commensurate with the weight of the user is that bushing that is too soft can cause wheel bites when cornering, with a consequent risk of falling. They can also make the board excessively unstable, especially when landing from a trick. On the other hand, bushing that is too stiff prevent light riders from turning the board.
In addition to the weight of the rider, the use we will make of the skateboard counts. For example, in the park stiffer bushing is used to keep the board stable during landings. Even in cruising and for long distances, it is preferable to choose fairly stiff rubbers that offer good stability and rebound. While in surfskate for carving, softer rubber pads are generally used which make the skate more unstable but allow you to steer more.
Of course it is also possible to mix the hardness of the bushing to have more targeted settings for your style.
Bushing shape
The shape of the Bushing is another factor to consider. There are three basic shapes: conical, cylindrical, and stepped. Conical and cylindrical bushing are the most popular.
These shapes can be mixed or used in pairs to have different performances.
Bushing Cone / Cylinder are the most common combination for skateboard, longboard and surfskate grommets because this is a very versatile setting.
The lower rubber pad is cylindrical in shape, a shape that allows the rubber pad to fit firmly in its seat, while the conical-shaped upper rubber increases the ability of the truck to lean and steer. Many skateboarders put a cylindrical, stiffer one underneath.
Cylinder / cylinder bushing As the name suggests, the upper and lower grommets are both cylindrical. This setting, often referred to as a downhill setting, offers superior stability which makes it the ideal choice for downhill and in all those situations in which stability is preferred over steering.
Bushing Cone / cone this setting includes two conical shaped rubber pads. This gives the truck a superior steering angle so it is the ideal combination for those looking for tight turns and carving and on surfskates when looking for extreme mobility and softness.
Bushing and types of skate trucks
Finally, be careful because not all bushes are the same size and therefore not all bushes fit all skateboard trucks. For example, skateboard bushes don't usually fit on surfskate trucks and vice versa. Here is a very concise overview of the main dipologies:
Skateboarding bushes are generally 10mm high (top one) and 14mm bottom one
Longboard bushes are generally 14mm (top) and 16mm (bottom) high.
In the surfskate it is a bit more complicated. Longboard type bushing is used on Truck cx or similar Cx. Skateboarding trucks are used on Yow or smoothstar trucks, just to name a few
High quality bushing
On the market, like anything else, you can find bushing of different quality and different prices, but what actually changes?
We have tried to use the famous orangtangs for example. The Bushing Orangatangs are considered by many to be among the best on the market for the quality of the urethane and are the ones fitted for example by the Bolsa skate loaded in collaboration with carver. As well as on the Bolsa we have also mounted and tested them on a yago dora carver with Cx truck and on a Triton and I must say that you can feel the difference.
The steering feels more precise and immediate. The feeling is more direct, even with very soft bushing like the ones we used.
Personally, we also found ourselves very very well with the Long Island bushes (those that are mounted on the Yow, Long Island skates and others that come out of the same factory). Also in this case we are talking about good quality urethane rubbers, not as cheap as others but capable of offering good rebound and good durability.
So the thing that is surely going through your head is "is bushing worth the money?".
The answer is that if you are not satisfied with the feeling of your skate or if your rubber pads are starting to get old and you need to change them, it is certainly worth spending a few euros more to buy quality rubber pads rather than just any rubber pads.
The biggest flaw we have found on poor quality rubber is that they do not have a good rebound, and this is perceived more on the softer ones.
When do i need to change my rubber tips?
Just like the wheels, the bushing of your skate will sooner or later wear out and will have to be changed.
To understand if they should be replaced it is enough to observe them. Has the rubber changed color, is it cracked or even deformed? When you pingi the skate doesn't go straight anymore? Do you continue to tighten the truck nut but the steering remains soft? It means that the time has come to give your table some new rubber tips ... he will thank you!